GTO GP-SW050 User Manual

OWNER’S MANUALGP-SW050Residential Duty Swing Gate OperatorWith Inherent UPS Battery Back-up SystemGPSW050 rev - 04/07/08Printed in China for GTO, i

7 Technical Specications Motor•BrushlessDCmotor24VDC300watts•½Horsepower•Maximummotorcurrent20Amp•2500RPM•Openandclosetimefo

8 Owner’s ManualOwner’s ManualGTO/PRO GP-SW050AC Powered Swing Gate OperatorsWARNINGReducer /Operator ArmGate Bracket1/2" Washer (2)Plastic Spac

9This unit must only be installed by an experienced technician.Preparation of the GateBefore installing the GTO swing gate operator, make sure:• the

10Using the Mounting TemplateThe mounting template (see insert)isdesignedtosimplifymountingtheoperator.Itprovidestheinstallerwiththepro

11Mounting Template (NOTTOSCALE)10”2½”3”11”6 3/8”4 5/8”Drill 3/8” x 3” deep6 places. Use 3/8”wedge type anchors.18½“ FromHinge Centerline7“ FromHing

12Removing the Operator HousingBeforeyoucangainaccesstotheoperatorframeanditsmountingholes,thehousingwillhavetoberemoved from the op

13RED WIRE to positive (+)JUMPER WIRE (Supplied)RED WIRE to positive (+)BLACK WIRE to negative (–)JUMPER WIRE (Supplied)negative (-) to positive (+)BL

14 IMPORTANT: Be sure the operator housing will not be hit by a fully open gate and that the gate column will not interfere when housing is installe

15 BoltsandWashersReducerArmKeyClosed GateClosingGate BracketOperator ArmReducer Arm(approx)5°-10° AngleClevis PinHairpin ClipOutput ShaftFig. 1Fig.

16Control Board Description1 2 3 4ONLOCKCOMCOMCOMALARMCYCLESAFETYSHADOWOPENCLOSESTOPOPENEDGECLOSEEDGESTATUSSTALL FORCE ADJUSTLIMIT ADJUSTMENTS

The GP-SW050 automatic gate operators are intended for use with vehicular swing gates. The operators can be used in Class I, II, III, and IV applicat

17COMCOMCOMOPENCLOSESTOPCLOSEEDGELIMIT ADJUSTMENTSTEST SWITCHESCLOSE STOP OPENGTO Inc. Tallahassee, FLSX4000 Logic Board Rev. EMIN MAX MIN MAX O

18Stall Force and Auto-Close AdjustmentsStall Force Adjustment: IMPORTANT: For safety reasons, the STALL FORCE potentiometers are set at the “10 o’c

191 2 3 4ONLOCKALARMCYCLESAFETYSHADOWOPENEDGESTATUSSTALL FORCE ADJUSTDUALLINKGTO LOOP DETECTORSLIMIT SENSORSDIAG. PORTBLDC SPEED CONTR

201 CYCLE:(Typicallyforusewithdoorbellbuttonorhardwiredkeypad) • Eachactivationatthisinputwillcycletheoperationasfollows: 

211 2 3 4ONLOCKCOMCOMCOMALARMCYCLESAFETYSHADOWOPENCLOSESTOPOPENEDGECLOSEEDGESTATUSSTALL FORCE ADJUSTLIMIT ADJUSTMENTSDUALLINKGTO LOOP DETE

22Output ConnectionsNote: • Maximumratingforallrelayoutputsare24Vac/dc,1Amp. • Allrelayoutputsaredrycontact(novoltage)switching.

23Accessory Power Supply Connection• 12Vdc@300mA(.3A)maximumpowersupplyforadditionalaccessories.• Ifyoulosepowertoyouraccessories,t

24Prison Mode Operation (CLASS IV APPLICATIONS)Prison mode operation means that constant pressure at the CLOSE or the OPEN push button station in

25Reinstalling the Operator HousingChecktomakesurethesafetyedges,photoelectricbeams,warningsigns,andpedestriangate(ifnecessary)areins

26• Thesetwo(2)terminalsprovidecommunicationconnectionsfordualgateapplicationswhereone  unit operates as a master and the other as sla

Table of ContentsGate Operator Class Categories ...InsideCoverMetr

27Setting Dual Gate SequenceGP-SW050operatorscomefromthefactorywiththe#2DIPswitchessettoOFF.DIP Switches must be changed to accommodate

28Safety EdgesWarning SignWarning SignSafety EdgeSafety EdgeMaster OperatorSlave OperatorUse Rigid Conduitfor inbound AC.Use Rigid Conduitfor inbound

29MaintenanceMaintenance Schedule:•Testtheoperator,accessories,andsafetydevicesmonthly.•Servicethegateoperator,accessories,andsafety

30TroubleShooting GuideWARNING: ALWAYS TURN OPERATOR OFF AND DISCONNECTBATTERIES BEFORE ADJUSTING OR SERVICING IT.SYMPTOM DIAGNOSIS CHECKOne beep eve

31SYMPTOM DIAGNOSIS CHECKCycle LED ON brightlyStatus Light ashesCycle terminal shorted to Com • Pushbuttonorkeyonkeypadis stuck.• Wire

32SYMPTOM DIAGNOSIS CHECKClose Edge LED ONbrightly Status LightashesCloseEdgeterminalshortedtoCom• Edgesensorissensingan obstruction.

33Warranty and Repair Service GTO AC Powered Gate Operator Limited WarrantyGTO AC powered gate operators are warranted by the manufacturer against def

Installation ChecklistThe installation of this operator conforms to CLASS __________.Theinstallerveriesthat(eachitemmustbechecked):____ Requi

1Important Safety InstructionsSAFETY INSTRUCTIONS FOR THE GPSW050 SWING GATE OPERATORSIMPORTANT SAFETY INSTRUCTIONS for the System DesignerWARNING:

2Important Safety InstructionsIMPORTANT SAFETY INSTRUCTIONS For the InstallerWARNING–To reduce the risk of injury or death:I. Before Installation 1.

3Important Safety InstructionsIMPORTANT SAFETY INSTRUCTIONS Specic to Secondary Means of Protection Against EntrapmentAsspeciedbyUnderwritersLab

4Important Safety InstructionsImportant Safety Instructions fortheConsumer/EndUserWARNING: To reduce the risk of injury or death: 1. READ AND FOL

5Important Safety InstructionsRequired Safety Precautions for GatesSafety Edge Safety EdgeSafety EdgePhoto BeamsWarning Sign Pedestrian GateVehicle Ga

6Important Safety InstructionsWarning Labels Thesewarningsignsandlabelsshouldbefoundatthelocationsspeciedbelow.Ifanyofthemaremissin